Setting Up Marco ARK, HandyRef, LM, RKT, & VL Series Equipment
The following models interact with
- ARK-1
- ARK-1a
- ARK-1e
- ARK-530A*
- ARK-700A*
- ARK-710A*
- ARK-730A*
- ARK-760A*
- ARK-F*
- LM-7**
- LM-7P**
- LM-500**
- LM-600**
- LM-990a**
- LM-1000**
- LM-1200**
- LM-1800**
- RKT-7700**
- M3 TonoRef II
- VL-3000
* Select ARK-A-Devices from the Marco device list in the Eyefinity Equipment Interface Setup window.
** Select LM-Devices from the Marco device list in the Eyefinity Equipment Interface Setup window.
For the device to transfer data to the equipment interface, you must set several parameters on your Marco equipment as follows:
- To access the Parameter Set screen and set each of the parameters, follow the instructions in your device manual.
- When you finish setting the parameters, exit Parameter Set mode, turn off the device, and turn it back on.
The following table shows the parameter number and setting for each of the parameters on each device.
| Device | KM Unit | I/F Mode | I/F Format | Baud Rate | Bit Length | CR Code | LDATA |
|---|---|---|---|---|---|---|---|
|
ARK-1 |
#3: D |
#51: NCP10 |
#52: All |
#53: 9600 |
#54: 8 |
55: No |
No |
|
ARK-1a |
#3: D |
#51: NCP10 |
#52: All |
#53: 9600 |
#54: 8 |
55: No |
No |
|
ARK-1e |
#3: D |
#51: NCP10 |
#52: All |
#53: 9600 |
#54: 8 |
55: No |
No |
|
ARK-530A |
|
#71: NCP10 |
#72: All |
|
|
|
|
|
ARK-700A |
#3: D |
#31: NCP10 |
#32: All |
#33: 9600 |
#34: 8 |
35: No |
|
|
ARK-710A |
#11: D |
#51: NCP10 |
#52: All |
#53: 9600 |
#54: 8 |
55: No |
|
|
ARK-730A |
#11: D |
#51: NCP10 |
#52: All |
#53: 9600 |
#54: 8 |
55: No |
|
|
ARK-760A |
#3: D |
#51: NCP10 |
#52: All |
#53: 9600 |
#54: 8 |
55: No |
|
|
ARK-F |
To set these parameters on this device, use the Marco Connect software. To download the Marco Connect software, contact Marco at 800.874.5274 or go to www.marcoconnect.com/downloads. |
||||||
|
HandyRef-K |
|
#71: NCP10 |
#72: All |
|
|
|
|
|
LM-7 |
|
NCP10 |
|
|
|
|
|
|
LM-7P |
|
NCP10 |
|
|
|
|
|
|
LM-600 |
|
Menu Page 5: #32 NCP10 |
|
#33: 9600 |
8 |
OFF |
|
| LM-990A |
To set these parameters on this device, use the Marco Connect software. To download the Marco Connect software, contact Marco at 800.874.5274 or go to www.marcoconnect.com/downloads. |
||||||
|
LM-1000 |
|
Menu Page 5: NCP10 |
|
Menu Page 5: 9600 |
Menu Page 5: 8 |
Menu Page 5: No |
|
|
LM-1200 |
|
Menu Page 4: NCP10 |
|
Menu Page 4: 9600 |
Menu Page 4: 8 |
Menu Page 4: No |
|
|
LM-1800 |
|
Menu Page 5: #32 NCP10 |
|
#33: 9600 |
8 |
OFF |
|
|
RKT-7700 |
|
#49: NCP10 |
#50: All |
|
|
|
|
|
M3 TonoRef II |
|
#81: NCP10 |
#82: All |
|
|
|
|
|
VL-3000 |
PC |
9600 |
8 |
ODD |
1 |
VL-3000 |
|